14 pin dip 5 tap low-profile ttl compatible active delay lines tap delays total delays part ?% or ? ns? ?% or ? ns? number 5, 10, 15, 20 25 ep9300 6, 12, 18, 24 30 ep9313 7, 14, 21, 28 35 ep9314 8, 16, 24, 32 40 ep9315 9, 18, 27, 36 45 ep9316 10, 20, 30, 40 50 ep9301 12, 24, 36, 48 60 ep9311 15, 30, 45, 60 75 ep9317 20, 40, 60, 80 100 ep9302 25, 50, 75, 100 125 ep9319 30, 60, 90, 120 150 ep9303 35, 70, 105, 140 175 ep9320 40, 80, 120, 160 200 ep9304 45, 90, 135, 180 225 ep9321 50, 100, 150, 200 250 EP9305 60, 120, 180, 240 300 ep9306 70, 140, 210, 280 350 ep9307 ? whichever is greater. delay times referenced from input to leading edges at 25?, 5.0v, with no load. tap delays total delays part ?% or ? ns? ?% or ? ns? number 80, 160, 240, 320 400 ep9308 84, 168, 252, 336 420 ep9318 88, 176, 264, 352 440 ep9322 90, 180, 270, 360 450 ep9309 94, 188, 282, 376 470 ep9323 100, 200, 300, 400 500 ep9310 110, 220, 330, 440 550 ep9330 120, 240, 360, 480 600 ep9324 130, 260, 390, 520 650 ep9331 140, 280, 420, 560 700 ep9325 150, 300, 450, 600 750 ep9329 160, 320, 480, 640 800 ep9326 170, 340, 510, 680 850 ep9332 180, 360, 540, 720 900 ep9327 190, 380, 570, 760 950 ep9333 200, 400, 600, 800 1000 ep9328 package dimensions e in pulse input voltage 3.2 volts p w pulse width % of total delay 110 % t ri pulse rise time (0.75 - 2.4 volts) 2.0 ns p rr pulse repetition rate @ td 200 ns 1.0 mhz pulse repetition rate @ td > 200 ns 100 khz v cc supply voltage 5.0 volts input pulse test conditions @ 25?c unit v oh high-level output voltage v cc = min. v il = max. i oh = max 2.7 v v ol low-level output voltage v cc = min. v ih = min. i ol = max 0.5 v v ik input clamp voltage v cc = min. i i = ii k -1.2 v i ih high-level input current v cc = max. v in = 2.7v 50 ? v cc = max. v in = 5.25v 1.0 ma i il low-level input current v cc = max. v in = 0.5v -2 ma i os short circuit output current v cc = max. v out = 0. -40 -100 ma (one output at a time) i cch high-level supply current v cc = max. v in = open 75 ma i ccl low-level supply current v cc = max. v in = 0 75 ma t ro output rise time td 500 ns (0.75 to 2.4 volts) 4 ns td > 500 ns 5 ns n h fanout high-level output v cc = max. v oh = 2.7v 20 ttl load n l fanout low-level output v cc = max. v ol = 0.5v 10 ttl load dc electrical characteristics parameter test conditions min max unit v cc supply voltage 4. 75 5.25 v v ih high-level input voltage 2. 0 v v il low-level input voltage 0.8 v i ik input clamp current -18 ma i oh high-level output current -1.0 ma i ol low-level output current 20 ma p w * pulse width of total delay 40 % d* duty cycle 40 % t a operating free-air temperature -55 +125 ? recommended operating conditions min max unit *these two values are inter-dependent. schematic dsd93xx rev. a 2/5/96 qaf-cso1 rev. b 8/25/94 unless otherwise noted dimensions in inches tolerances: fractional = ?1/32 .xx = ?.030 .xxx = ?.010 16799 schoenborn st. north hills, ca 91343 tel: (818) 892-0761 fax: (818) 894-5791 e l e c t r o n i c s i n c . 12 4 10 6 8 1 7 output ground input 14 vcc .365 max. .780 max. .280 max. pca ep93xx date code .010 typ. .100 min. .015 typ. .165 max. .020 typ. white dot pin#1 .100 .300 .200
|
